|
GASKETS
Measuring For A Gasket
- Gasket mounts fall into one of four styles: screw-on, snap-in,
push-in or panel gripper.
- Compare your gasket to the profile provided on our website. Compare
thickness, width and magnet width.
- All standard gasket frame dimensions should be measured edge
from edge even if the gasket has snap-in-darts. (Of Special Note:
when measuring for custom made gaskets; screw-in style, measure
edge to edge. When measuring snap-in style, measure dart to dart.)
Pre- Installation Tips
- Allow replacement gasket to reach room temperature before unfolding.
- Carry gasket by its corners and avoid squeezing folds to prevent
breaking the internal magnet.
- Thoroughly clean the area with soap
and water, to insure proper installation.
LATCHES & HANDLES
Adjustment
A series of parallel grooves and slotted holes that will mate with
another grooved area. While the screws are loose, the latch or strike
can be moved the full travel of the slotted holes. When the screws
are tight the grooves mate, holding the item at the proper adjustment.
Using the incorrect screw size can reduce or eliminate the adjustment.
A Micro turn strike can be adjusted by backing out the set screw,
screwing the hook in or out, and re-tighten set screw.
Edgemount
This refers to a latch that mounts vertically on the side of the
door as opposed to mounting on the front face of the door. Most
reach-in doors have edgemount latches.
External Mounting
This refers to pull handles. The screws for the handles install
from the front of the door.
Internal Mounting
This refers to pull handles. The screws for the handles install
from the inside of the door.
Latch Only
This refers to the body of the latch which mounts on the door.
Latch Complete
This refers to both body and strike.
Magnetic/Mechanical
This refers to the catch mechanism. Some latches have a magnet that
holds the door closed. Mechanical latches have a hook that holds
the door closed. Some latches are both mechanical and magnetic.
Offset
Refers to the distance between the face of the unit and the front
of the door. Offset will only apply to a surface mount latch.
Offset Handle
Is a vertical latch with a "dog leg" lever. The lever
extends past the door allowing easy access in tight situations.
Screw Centers
These are used to help identify hardware. The measurements are taken
from the center of the screw holes.
Straight Handle
This refers to a vertical latch running flush with the edge of the
door. This provides additional protection from abuse.
Strike Only
This refers to the catch which mounts on the face of the box.
Surface Mount
This refers to latches that mount horizontally on the front face
of the door.
HINGES
Adjustment
This is an area with a series of parallel grooves and slotted holes
that will mate with another grooved area. While the screws are loose,
the hinge can be moved the full travel of the slotted holes. When
the screws are tight the grooves mate, holding the item at the proper
adjustment. Using the incorrect screw size can reduce or eliminate
the adjustment.
Cam-Rise
This refers to hinges with a self closing feature. As the door opens,
the cam lifts the door. The weight of the door closes the door.
Edgemount
This refers to a hinge that mounts vertically on the side of the
door as opposed to mounting on the front face of the door. Or the
top and bottom of the door.
Offset
This is the distance between the face of the unit and the front
of the hinge.
Pivot
These are hinges that mount on the top and bottom of the door allowing
the door to pivot open.
Screw Centers
These are used to help identify hardware. The measurements are taken
from the center of the screws holes.
Spring Assist Hinges
These are hinges that create a self closing door. They must be used
with a magnetic gasket or use a non-magnetic gasket and a magnetic
latch. Do not expect the spring's power to hold a door closed or
close a mechanical latch.
Surface Mount
This refers to hinges that mount horizontally on the front of the
face of the door.
|
